Oxygen sensor principle

Oxygen sensor overview
All oxygen sensors are self-powered and have limited diffusion. The metal-air battery consists of an air cathode, anode and electrolyte.
The oxygen sensor is simply a sealed container (metal or plastic container), which contains two electrodes: the cathode is a piece of PTFE (polytetrafluoroethylene) coated with an active catalyst, and the anode is a lead block. This sealed container only has a capillary hole on the top, allowing oxygen to pass into the working electrode. The two electrodes are connected to the two pins protruding from the sensor surface through the current collector, and the sensor is connected to the applied device through the two antennae. The sensor is filled with electrolyte solution, so that different kinds of ions can be exchanged between the electrodes (see Figure 1).

Figure 1-Schematic of oxygen sensor.
The flow rate of oxygen into the sensor depends on the size of the capillary pores on the top of the sensor. When oxygen reaches the working electrode, it is immediately reduced to release hydroxide ions:
O2 + 2H2O + 4e- "> 4OH-
These hydroxide ions reach the anode (lead) through the electrolyte and undergo an oxidation reaction with lead to produce the corresponding metal oxide.
2Pb + 4OH- "> 2PbO + 2H2O + 4e-
The above two reactions generate a current, and the current depends on the oxygen reaction rate (Faraday's law). A known resistance can be connected to measure the resulting potential difference, so that the oxygen concentration can be accurately measured. In the electrochemical reaction, the lead electrode participates in the oxidation reaction, making these sensors have a certain life span. Once all the available lead is completely oxidized, the sensor will stop functioning. The service life of an oxygen sensor is usually 1-2 years, but the service life of the sensor can also be extended by increasing the anode lead content or limiting the amount of oxygen contacting the anode.
Capillary micropore oxygen sensor and partial pressure oxygen sensor
The oxygen sensor produced by City Technology is divided into two types according to the diffusion of oxygen into the sensor. One is a capillary hole on the top of the sensor, and the other is a solid film to allow gas to pass through. The pore sensor measures oxygen concentration, while the solid film sensor measures oxygen partial pressure.
The current generated by the fine-pore sensor reflects the volume percentage concentration of the measured oxygen, regardless of the total gas pressure. But when the oxygen pressure changes instantaneously, the sensor will generate an instantaneous current, and problems will occur if it is not properly controlled. The same problem occurs when the sensor is subjected to repeated pressure pulses, for example, the gas entering the sensor is pumped. The explanation for this phenomenon is as follows:
Pressure transient
When the fine-pore oxygen sensor encounters a sharp pressure increase or decrease, the gas will be forced through the fine-pore grid (large flow). The increase (or decrease) of the gas produces a transient current signal. Once the situation has stabilized and there are no more pressure pulses, the transient is over. Such transients can be alerted by the instrument, so CityTech can work hard to find a solution to reduce the impact of pressure.
All urban technology's fine-pore oxygen sensors use anti-high flow mechanisms, see Figure 2. Basically, a PTFE anti-high-flow membrane can be added to reduce the transient effects of pressure changes. This layer of film is tightly fixed to the fine hole with a metal or plastic cover. This design can greatly reduce the impact of instantaneous signal changes.

Figure 2-Bulk Flow Membrane on Capillary Sensor
However, the transient force generated by some pressure changes exceeds the allowable range of this design, especially the equipment that uses extractive instruments to deliver gas to the sensor. The gas produced by some pumps causes a continuous pressure pulse on the CiTiceL oxygen sensor, artificially enhancing the signal. In this case, it is necessary to design a gas expansion chamber outside the sensor to reduce the pressure pulse to the sensor.
Partial pressure type oxygen sensor
Capillary pores to control gas diffusion are not the only way to control oxygen entering the sensor. We can also use a very thin plastic film to cover the top of the sensor to disperse oxygen molecules before entering the sensor (Figure 3).

Figure 3-Solid Membrane (partial pressure) oxygen sensor
The flow rate of oxygen into the working electrode is determined by the partial pressure of oxygen through the membrane. This means that the output signal of the sensor is proportional to the partial pressure of oxygen in the mixed gas. A change in atmospheric pressure will cause a corresponding change in the sensor output current. If you use extractive gas delivery, you must ensure that the pulse force does not affect the sensor during the design stage of the device.
City Technology produces two types of partial pressure oxygen sensors, AO2 / AO3 (automotive) and MOX (medical), which are solid film type, the response relationship is linear, and the range is 0-100%.
Linear relationship
The signal from the fine pore oxygen sensor is non-linear and has the following relationship with the oxygen concentration (c):
Signal = constant * ln [1 / (1-C)]
In fact, the output of the sensor rises linearly, and the deviation does not occur until the oxygen concentration exceeds 30%, which makes measurement difficult. The linear output of the partial pressure sensor can reach 100% oxygen (or 1.0% oxygen concentration).
temperature
Fine-pore and thin-film oxygen sensors are sensitive to changes in temperature, but they have different degrees of sensitivity.
The effect of temperature on the fine-pore oxygen sensor is relatively small. Usually the temperature from + 20 ° C to –20 ° C will cause a 10% loss of the output signal. In contrast, the temperature has a much greater effect on the thin film oxygen sensor. Gas diffusion through the thin film is an active process. Usually a temperature change of 10 ° C will cause the sensor signal output to double. Thin film oxygen sensors require relatively stable temperature, so many CiTiceLs? Products have built-in thermistors.
Active reserve
When designing any electrochemical sensor, the grid (film or pores) should be used to limit the gas passing rate, while the other stages are significantly faster. Therefore, in order to ensure the speed of the electrochemical reaction, electrode materials with high catalytic activity must be used.
All CiTiceLs? Products use highly active electrodes to make the sensor have high activity reserves, ensuring the long-term stability and low drift of the sensor.
typical application:
Gas-Oxygen Application-Industrial Safety Choice-0-30%;
series
Gas type
product name
Related downloads
Oxygen sensor principle.pdf
I want to contribute
2020 National Education Equipment Cloud Exhibition
Purchasing QR code

Sweep, welcome attention

Official WeChat of Educational Equipment Procurement Network

Master the latest and most authoritative information in the education equipment industry

Copyright and Disclaimer:

â‘  The copyright of all works on this website that indicate "Source: China Education Equipment Purchasing Network" belongs to China Education Equipment Purchasing Network, and may not be reproduced, edited or used in other ways without authorization from this website. Works that have been authorized by this website should be used within the scope of authorization, and indicate "Source: China Education Equipment Purchase Network". Violators of this website will be held accountable for legal liabilities.

â‘¡ All works on this website that indicate "Source: XXX (non-this website)" are reproduced from other media. The purpose of this reprint is to transmit more information. This does not mean that this website agrees with its views and is responsible for its authenticity. Take direct responsibility and joint liability for infringement of such works. If other media, websites or individuals download and use it from this website, they must keep the "source of the manuscript" indicated on this website, and bear the legal responsibility of copyright and other.

â‘¢ If the content of the work, copyright and other issues are involved, please contact this website within two weeks from the date of publication of the work, otherwise it is deemed to waive the relevant rights.

Guangzhou Aoweiya Electronic Technology Co., Ltd.
Latest equipment
More
NES non-contact concrete shrinkage deformation tester
NES non-contact concrete shrinkage deformation tester HKG-1047 Knee Trainer
HKG-1047 Knee Trainer Multi-channel gas synchronous controller
Multi-channel gas synchronous controller Hydroxylamine hydrochloride-premium grade pure reagent price
Hydroxylamine hydrochloride-premium grade pure reagent price Dymola — Multidisciplinary system simulation platform
Dymola-Multidisciplinary system simulation platform Mobile socket
Mobile socket Sponge foam tensile tear strength testing machine
Sponge foam tensile tear strength testing machine Data collection high efficiency wet dust collector
Data collection high efficiency wet dust collector Shuhua Brand Outdoor Fitness Path (Plastic Wood Series) SH-04014 four-position pedal [Please fill in the core parameters / selling points]
Shuhua brand outdoor fitness path (plastic wood series) SH -... Beijing vehicle weather system / integrated weather system / small meteorological instrument
Beijing vehicle weather system / integrated weather system / small ...
Interview
More
Qingdao Xinxin Sports: Why does Star shine for a long time?
Qingdao Xinxin Sports: Why does Star shine for a long time? Body Story Brand Story│Wilson's Three Logics in the Rise of Basketball
Body Story Brand Story│Wilson's Three Logics in the Rise of Basketball
Qingdao Xinxin Sports: Why does Star shine for a long time? Body Story Brand Story│Wilson's three rises in basketball ... Tonghui Information: Creating VR Immersive Interactive Learning Environment for Students Blog Robot: Empowering Robot Education to Realize China's Intelligent Dreams and Convincing Technology to Make IT More Valuable Lida data helps predict the development of disciplines
Equipment observation
More
The focus of school sports equipment procurement in February 2020 is focused on "Shandong". In February 2020, the school software system procurement in Shaanxi is far away ... In February 2020, the school training equipment procurement in Fujian is ahead of the project in February. , Hebei, Hubei ranked ... School monitoring and procurement in February 2020: basic education accounted for 73% of the school logistics procurement in February 2020, Shandong transaction project is still outstanding
Solution Case
More
China Railway Eighteenth Bureau ZT801 rock mass parameter measuring instrument put into use
China Railway Eighteenth Bureau ZT801 rock mass parameter measuring instrument put into use Huake Feiyang Announces "Sound and Body Beauty" Interactive Delivery Class
Huake Feiyang Announces "Sound and Body Beauty" Interactive Delivery Class Xiaoyu Yi Lianyun video conference helps 2 million teachers and students in more than 50,000 classrooms
Xiaoyu Yi Lianyun video conference helps 2 million teachers and students in more than 50,000 classrooms Yunnan "first class of school" Xiaoyu Yilian assisted more than 50,000 classrooms with 2 million teachers and students
Yunnan "first class of school" Xiaoyu Yilian assisted more than 50,000 classrooms with 2 million teachers and students
Newly settled
More
Beijing Zhuoli Hanguang Instrument Co., Ltd. Beijing Sibote Sports Equipment Co., Ltd. Hebei Jiaguan Furniture Co., Ltd. Fujian Woko Education Information Technology Co., Ltd. Nanjing Changxun Information Technology Co., Ltd.
Government Procurement
More
[Tendering] Competitive consultation on the procurement of fire extinguisher repair services ... [Winning bid] Winning the bidding of the procurement project of the academic service management platform ... [Tendering] Competitive consultation on the affiliated project of Yangjiayao Kindergarten ... [Other] Qingcheng Town The school sports ground renovation project changes ... [Others] The tables and chairs and multimedia equipment of the library report hall are scrapped ... [Winning bid] Postgraduate thesis submission service procurement project ... [Others] The second correction of the campus network upgrade and reconstruction project. .. [Other] Correction Announcement of Student Bedding Procurement Project [Other] Announcement of Correction of Car Rental Service [Other] Split Air Conditioning of Student Dormitory in West Campus of Shenzhen Campus
var _hmt = _hmt || []; (function () {var hm = document.createElement ("script"); hm.src = "//hm.baidu.com/hm.js?7bba69eb3c3832c2e03cd64b565141fc"; var s = document .getElementsByTagName ("script") [0]; s.parentNode.insertBefore (hm, s);}) (); (function () {var bp = document.createElement ('script'); var curProtocol = window.location .protocol.split (':') [0]; if (curProtocol === 'https') {bp.src = 'https://zz.bdstatic.com/linksubmit/push.js';} else {bp .src = 'http://push.zhanzhang.baidu.com/push.js';} var s = document.getElementsByTagName ("script") [0]; s.parentNode.insertBefore (bp, s);}) ();

Customized CAD canister toys can be designed, proofed and produced by professional designers according to the drawing, template and design drawings provided by customers. Provide an impressive and perfect series of CAD canister toys at a reasonable price.

Custom Cad Can Toy


Genuine promises: All our products, quality assurance, please rest assured to purchase orders.
About the delivery date: We have a strong team to serve you, to ensure that customers order the delivery date.
About packing: We use punched plastic bags to prevent children from danger. The material of plastic bags can be provided by customers. We can produce them as required. Cartons, colour boxes and other packages can be customized according to customers'requirements.
After-sale service:If there are any quality problems in our products, we can unconditionally replace them.
The company's products with environmental protection materials, excellent workmanship, all kinds of supporting facilities, advanced technology, perfect management, excellent quality, reasonable price, rapid development, strict confidentiality, complete after-sales service. Only detailed product drawings (or samples) are required to provide customers with one-stop service from development to after-sales service.

Map customization:We have professional designers who can design according to your requirements. You only need to provide pictures of toys (physical objects or floor plans) to customize the products you want.

Custom Cad Can Toy


Custom Cad Can Toy

Custom Cad Can Toy,Quality Cad Can Toy,Cheap Cad Can Toy,Plastic Cad Can Toy

SHEN ZHEN HAO XIAN LONG TECHNOLGY.CO.,LTD , https://www.haoxianlongtoys.com

Posted on