Toto smart toilet cover installation method detailed installation attention

With the development of intelligence, all aspects of our lives are inseparable from smart products, even the bathroom products have also produced smart toilet lids, and as the toto brand with more types of toilets in the industry, its smart toilets are not Inferior to other similar products. Let me explain to you if you buy a smart toilet cover, just toto brand, how to install correctly, what issues should be paid attention to during the installation process.

Toto smart toilet cover installation method

Many people worry that the toto smart toilet cover will not be complicated to install, in fact, just pay attention to three steps.

1. Before installation, a water stop valve must be installed to disconnect the water source during maintenance or repair. Otherwise, you will encounter a lot of troubles during maintenance. When installing, you must use the level to measure the position to keep the front, back, left and right at the same level, otherwise the siphon effect or the scrubbing effect will be bad. Install the toilet seal. These are consistent with non-intelligent products to prevent leaks in the drain pipe, resulting in poor siphoning or spillage.

2. The smart toilet needs to be powered, and the installation environment is high. The toilet must have a power outlet. To keep the power outlet at a distance of 0.8 m above the ground and try to keep away from water, such as bathtubs and faucets, you must ground the cable. For safety reasons, it is recommended to install a leakage protector or an isolation transformer, and the power outlet must be a three-hole socket.

3. Pay attention to the water pressure of the influent water. Some intelligent automatic toilets are designed without water tanks, so the water pressure of these products is different from that of ordinary toilets. The water inlet requirement is 0.07MPa (20L/Min flow) to 0.75MPa (hydrostatic pressure). Need to test before ending the installation. Before connecting the toilet waterway to the water stop valve, first open the water valve to drain some water just inside to prevent the impurities from clogging the smart toilet inlet valve.

What are the installation precautions?

First, before installing the toilet, the sewage pipeline should be inspected thoroughly to see if there are any mud and sand, waste paper and other debris in the pipeline. At the same time, check whether the floor of the toilet seat is horizontal or not. If the ground is found to be uneven, install it. Level the floor when using the toilet.

Second, determine the center of the sewage pipe, and draw a cross center line. Flip the toilet, determine the center on the toilet drain, and draw the cross center line. The center line should extend to the bottom of the bottom of the toilet.

Third, determine the installation position of the bottom foot screw of the toilet bowl, use the impact drill to lay the installation hole, and pre-embed the plastic rubber sleeve of the expansion screw. Install a special sealing ring on the toilet drain, or put a circle of glass glue (putty) or cement mortar around the drain pipe. The ratio of cement to sand is 1:3.

4. Align the crosshair on the toilet with the crosshair of the ground drain. Install the toilet and press the seal tightly. Then install the anchor and the decorative cap, and then put it on the bottom of the toilet. A circle of glass glue (putty) or cement mortar, the ratio of cement to sand is 1:3, and the toilet is installed to maintain the level of front, back, left and right.

5. Install or debug the water tank fittings. First check the water pipe, drain the water 3-5 to flush the pipe to ensure the cleaning of the water pipe; then install the angle valve and the connecting hose, then connect the hose to the installed water tank fitting inlet valve and press the water source to check the inlet valve. Whether the water inlet and sealing are normal, check whether the installation position of the drain valve is flexible, whether there is any jam or leakage, and check whether there is a leaking inlet valve filter device.

6. If abnormalities are found during the commissioning process, please refer to the “Common Troubles and Handling Methods for Toilets and Water Tank Accessories” for inspection and treatment. Install the toilet cover.

7. After the toilet is installed, wait until the glass glue (soot) or cement mortar is solidified before releasing the water. The curing time is generally 24.

The difference between the installation method of toto intelligent toilet cover and the ordinary toilet installation method is not big, but it is also the difference in details that gives us a more comfortable experience, and the precautions in the installation process can also be used for the future. Use toto toilet to reduce a lot of trouble, I believe that everyone will be able to use more intelligent products in the future life, Xiaobian will continue to provide you with more knowledge content.