No horizontal printing (below)

12. Toray plate construction:
1 aluminum substrate;
2 glue layer;
3 photosensitive layer (thermosensitive layer);
4 silicone layer;
5 composition of the protective layer.
The photosensitive layer and the positive film type are photosensitive combined type, and the negative film type is a different functional structure of the photosensitive decomposition type.
13. Development steps:
1 except protective film;
2 Pre-swelling;
3 Bristles are developed to remove the peeling part of the sealant;
4 stain developed impressions.
It can be printed without dyeing, but the dyeing can be identified and scanned by the imprinter. The silicone film is removed from the mouth and the end of the plate. The positive film is not sensitive, and the negative film is sensitive, so that there is astringent resistance without sliding the clamping plate. .
14. With anhydrous ink, it can produce a very thin layer of liquid on the surface of silicone to prevent the ink from sticking and not sticking. In the past, it used oyster sauce because the unfavorable catalyst was not used in the post combustion system.
15. No horizontal printing Because there is no cooling effect of the evaporation of the water, the ink roller may rise 15°C above the 10,000 copies of the leaf printing machine, which is higher than the water with 8～10°C. It is unfavorable to keep the non-print part when printing. No sticking ink, the ink is divided into HNL and LL four kinds of anti-split force, but also in response to different printing speed and temperature conditions.

16. It is necessary to control the layout and the ink roller temperature in the range of ±1.5°C. Some inks are only ±0.8°C tolerant, while others are ±1.5°C. The temperature is too high will cause dirty, the temperature is too low, the ink migration is bad, and the full version is not White spots actually occur. Therefore, there is no horizontal printing conversion ink balance technology into a more manageable temperature control. In principle, there must be warm water and chilled water facilities in order to maintain the smooth start-up and printing works.
17. No horizontal printing advantages:
1 Printing is easy to balance with no ink balance.
2 Ink concentration is high and stable.
3 fine print dot reproduction.
4 can print about 400 lines, high fax prints.
5 Reduce the occurrence of waste paper.
6 Work efficiency can be improved.
7 Small printing is easy.
8 Press Construction Simplified.
The 9th edition has a strong contrast.
10 Paper stretches less.
11 Talent training is easy.

18. Unable to imprint defects 1 Patent version and ink are more expensive. Changes in the configuration of the press must be cooled. 3 printing plates have protective film can not be automatically developed to produce 4 rubber layer intolerant of friction. 5 revision fill is not easy. 6 Unsensitized plates are susceptible to aging dark reactions. Version 7 is harder to adjust to skin color and light color prints. 8 consumes large amounts of ink.
19. The waterless leaf-leaf printer is easy to find because many leaf machines have ink-ink roller cooling systems to keep the plate and the ink supply system at a constant temperature, but different considerations for the printing ink.
20. Waterless wheel precision lithography machine has MN Rolancl polyman. KBA Crotina, no water wheel transfer printer.
21. The single-fluid non-wetting system printing method uses the traditional watermarked and ink-mixed emulsified ink, but it is very important to replenish the water.
22.DI machine-to-plate conversion has a horizontal printing plate, and it is more convenient to use other external plate making methods.
23. There is no horizontal printing in the non-absorption inside with UV light on the plastic surface Credit card, CD-ROM use a lot of development prospects are very good.
24. The thermal CTP levelless printing plate will become the mainstream, and the dominant levelless printing development is mainly due to the advantages of short project, good quality, and high printing capacity that can improve the technical difficulty of personnel.
The principle of imprinting imaging relies on the destruction of the molecular bonds between the thermal layer and the silicone layer by the laser under the red light.
After the preprocessed plate is disintegrated, the silicone layer of the print portion will be peeled off during processing.
The embossed portion is embedded and molded on the ink-receptive polymeric surface layer. The ink can be firmly fixed in the hole structure to form a better regeneration dot.